NO HOT WATER? Follow These Simple Tips

Book A Service Call

We've encountered this post involving What Would Cause My Electric Water Heater to Stop Working? below on the net and concluded it made good sense to relate it with you here.


How to Troubleshoot and Repair an Electric Water Heater
Lots of contemporary homes take advantage of an electrical water heater for their heating system, because of its convenience as well as simplicity of use. Nonetheless, much like any other electrical devices, problems might occur with its use, suddenly. It can be really irritating to get up to a cold shower rather than a hot one or having your bathroom with water that isn't hot adequate or even also hot. Whatever the instance may be, hot water heater issues can be quite stressful. Fortunately, we've made a checklist of possible options to your hot water heater issues. There are a variety of factors that might create most of these problems, maybe a concern with the power supply, the electric heating element, or the thermostat. Before doing anything, guarantee you turn off the main power supply for security. Whatever the trouble is, getting it fixed must not posture too much of an issue if you comply with these actions:

Inspect Your Power Supply:


As fundamental as this might seem, it is very needed. Without ample power, your water heater will not work. So the first thing to do when your water unexpectedly retires is to confirm that it isn't a power problem. Inspect if the fuse is burnt out or the circuit breaker tripped. If the breaker is the problem, simply transform it off and on once more. Change any busted or worn-out fuse. Test the home appliance with power after these modifications to see if it's currently functioning.

Check the Burner in the Hot Water Heater:


If it's not a power issue, then attempt taking a look at your heating element if it is still functioning. Check each of your heating elements to be sure the problem isn't with any one of them. If any one of them is defective, change that part and then inspect whether the hot water is back on.

Examine Your Thermostat:


If your water heater still isn't working or the water appearing isn't hot enough, you may need to check the temperature setups on your top thermostat. Make certain the breaker is switched off before doing anything. Open the access panel as well as press the red switch for temperature level reset above the thermostat. This should help heat up the water. Turn the circuit breaker back on as well as inspect if the trouble has actually been fixed.

Call An Expert:


If after replacing all defective parts and resetting your temperature, the water heater still isn't functioning, you might require to get in touch with a professional plumber for a professional opinion. The problem with your heating system could be that the cold and hot faucets have actually been changed or it may be undersized for the amount of warm water required in your house. Whatever the case might be, a specialist plumber would certainly assist solve the trouble.

Verdict


Hot water heater issues are not always significant. Much of them are because of minor problems like a blown fuse or worn-out burner. Changing the defective parts need to work. However, if you are still unable to address the issue, give a call to your nearest plumber ahead to get it taken care of.

8 possible reasons why you have no Hot Water


Along with streaming Netflix and having light flood a room when we flick a switch, having hot water flow from our taps and showerheads whenever we want is an oft-overlooked modern miracle of homeownership. That's why, when that flow goes cold, it can be shocking — and not just in a "Wow, that's freezing" kind of way while you're in the shower.


Water Leak


Before hot water reaches your taps and showerheads, it needs to spend some time in your water heater. This appliance, which can be either gas- or electric-powered, takes the cold water that enters your home from your well or utility company and cooks it until it gets hot. It's akin to an electric tea kettle.



Obviously, if your water heater is leaking, it will never fill with water so it won't have anything to warm. To see if this is the case, simply examine the area around the water heater to see if it is wet. If so, you'll likely need to replace the unit, but you can also call in a pro for a second opinion and to see if it is fixable. Sometimes leaks can happen around fixtures on the water heater, and if so, the solution might be as simple as replacing them.


Gas Heater: Gas Leak


If your hot water is fueled by natural gas and there is a leak in the supply line or where the line enters the tank, the appliance won't have the power it needs to heat up your water. The result is not only inconvenient, but it can be extremely dangerous as well. If you smell gas when you investigate your water heater, call your gas utility company immediately and report it as an emergency. It might also be prudent to leave your home until a repair person from the company arrives. Your utility company will usually fix any kind of gas leak. However, in terms of getting your water heater working again, you'll need to relight the pilot and wait a while to see if it is functioning properly. You can call in a water heater specialist or plumber to help with this.


Gas Heater: Pilot Light Problems


There are two other issues with gas-powered water heaters that can lead to a loss of hot water. The first is a pilot light that's blown out. The pilot light is the source of a constant flame inside your water heater. When the heater determines the need to heat up the water it is holding, it will open a valve that will cause gas to flow over the pilot light and cause it to ignite. To see if your pilot light is functioning, there is usually a small window in the front of the water heater. If you can't see a flame, remove the access panel and see if that helps you locate it. If there is still no flame, you'll need to relight it in accordance with the manufacturer's instructions.



Your pilot light should burn with a bright blue flame. If not, make sure there are no drafts affecting it, which could keep it from functioning properly. If the flame looks yellow, it might be a sign of the presence of carbon monoxide, which spells trouble and needs to be looked at right away by a technician.


Gas Heater: Faulty Thermocouple


The second reason why a gas-powered water heater might fail is a faulty thermocouple. This is a small probe that should sit in the pilot light flame. Its purpose is to stop the flow of gas if it senses that the pilot light is out. Sometimes, these probes get knocked off track, so make sure it is directly in the flame. They can also get a buildup on them that prevents their function, so try cleaning yours off with some steel wool or fine-grit sandpaper. If your pilot light won't stay lit and you've tried these steps to fix the thermocouple, it is likely faulty and needs to be replaced. Call a technician.


Electric Heater: Breaker Blues


Electric water heaters don't have pilot lights, because there is no gas to burn in order to heat up the water. Instead, they do their magic through the use of (naturally) electricity. But that's not to say things can't go wrong with them. If your electric water heater isn't working properly, there's a good chance that a breaker was tripped that supplies the appliance power. Check your breaker box and flip any breakers that have switched to the off position back on. If it trips again, then there might be a fault in the water heater, and you'll want to call in a pro to have a look.


Electric Heater: Reaching The Limit


If the breaker is fine, check to see if the high-temperature limit has switched off on the water heater itself. To do so, first turn off the breaker to the unit. Then remove the service panel and press the red button you'll find there. This is the limit switch, and resetting it could solve your problem. To check, replace the panel, turn the breaker back on and listen to see if the water heater is functioning again.


Electric Heater: Heating Element


If these steps don't fix the issue, then you might have a failed heating element, which will need to be replaced. Unless you are comfortable with such repairs, calling in a technician might make the most sense.

https://www.homeserve.com/en-us/blog/home-improvement/no-water-heater/


No Hot Water — Water Heater Repair

Do you really like reading up on What Would Cause My Electric Water Heater to Stop Working?? Write feedback down below. We will be pleased to hear your ideas about this content. Hoping that you visit us again later on. If you appreciated our article if you please do not forget to pass it around. Thanks a lot for your time spent reading it.




Free Estimate

Leave a Reply

Your email address will not be published. Required fields are marked *